Slackware 10.2 i Wirless Optical Mouse

[HacKing]

Imam Verbatim Wirless Optical Mouse i sa ubuntom je radio ok.
Juce sam probao da instaliram slackware 10.2 i bio sam odusevljen cak sam uspeo da podesim i grafiku koju nisam uspeo da podesim ni na jednoj drugoj distribuciji.
Medjutim mis ne radi. Inace kad sam instalirao stavio sam na usb mouse.
Ima li pomoci?

[urke]

Pogledaj /etc/X11/xorg.conf i pronađi sekciju gde se podešava miš, pa vidi koji je uređaj određen za miša. Onda pogledaj u /var/log/Xorg.0.log (ili tako nekako) i vidi šta ti u njemu piše za uređaj na kome se očekuje miš (ili prikači taj log fajl u odgovoru ovde na forum da pogledamo).

[HacKing]

Valjde je ovo bitno

# Core Pointer's InputDevice section
# ************************************************** ********************

Section "InputDevice"

# Identifier and driver

Identifier "Mouse1"
Driver "mouse"

# On platforms where PnP mouse detection is supported the following
# protocol setting can be used when using a newer PnP mouse:

# Option "Protocol" "Auto"

# The available mouse protocols types that you can set below are:
# Auto BusMouse GlidePoint GlidePointPS/2 IntelliMouse IMPS/2
# Logitech Microsoft MMHitTab MMSeries Mouseman MouseManPlusPS/2
# MouseSystems NetMousePS/2 NetScrollPS/2 OSMouse PS/2 SysMouse
# ThinkingMouse ThinkingMousePS/2 Xqueue
Option "Protocol" "PS/2"

# The mouse device. The device is normally set to /dev/mouse,
# which is usually a symbolic link to the real device.

Option "Device" "/dev/mouse"
# Option "Device" "/dev/psaux"
# Option "Device" "/dev/ttyS0"
# Option "Device" "/dev/ttyS1"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option "BaudRate" "9600"
# Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

# Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"

# ChordMiddle is an option for some 3-button Logitech mice

# Option "ChordMiddle"

EndSection

# Some examples of extended input devices

# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection

[urke]

E samo promeni, ovo

Option "Device" "/dev/mouse"

zakomentariši a odkomentariši ovo:

# Option "Device" "/dev/psaux"

i javi rezultate.

[HacKing]

urke kaže:

E samo promeni, ovo

Option "Device" "/dev/mouse"

zakomentariši a odkomentariši ovo:

# Option "Device" "/dev/psaux"

i javi rezultate.

Ako mislis na ovo:

# Option "Device" "/dev/mouse"
Option "Device" "/dev/psaux"
# Option "Device" "/dev/ttyS0"
# Option "Device" "/dev/ttyS1"

I dalje nece da radi

[HacKing]

Da li mozda treba da se promeni ovo:

Option "Protocol" "PS/2"

[brainZ]

HacKing kaže:

Da li mozda treba da se promeni ovo:

Option "Protocol" "PS/2"

Upravo - protokol treba da bude "IMPS/2", a uredjaj /dev/input/mice

[HacKing]

Probao sam i dalje ne radi.

[niceness]

Da li ti mis radi sa gpm (da li mozes da ga koristis u terminalu)?
I daj da vidimo sta pise u /proc/bus/usb/devices (dok ti je prikljucen mis, naravno )

[HacKing]

Ne mogu da ga koristim u terminalu i ne postoji taj fajl.

[niceness]

Probaj da mountujes usbfs:

# mount -t usbfs none /proc/bus/usb

pa onda vidi sta pise u /proc/bus/usb/devices

[DJ_MY_SOUL]

I ja imam taj problem! Isto slack 10.2 mis i tastatura su mi komplet Logitech Cordless internet pro. Tastatura radi naravno, a mis mi se pomera kada pritisnem jednom levi clcik za 1 pixel u desno. Zanimljivo je da mi na slax-u (live verzija) radi fenomenalno sve!

[ROCK4EVER]

Ja sam odustao. Sve sam probao sto ste mi rekli i nista nece. U svakom slucaju hvala na odgovorima.